I ordered and installed this ignition on my 76 gl1000, followed all the instructions but I am having issues timing it. I hooked up the test light and timed it as the instructions say. Test light fires at F2 when connected to the blue wire and fires at F1 when connected to the yellow, but it also fires and will stay on at other points in the engines rotation. Tried to fire the bike up and it will start but will not go above 1,000 rpm and dies when I let off the throttle. Is it possible I have a faulty module? View answer
Asked 3 ´years ago
I want to install a DS6-1 Ignition system to my 84 GD Evolution motor. The motor is stock 80ci, I have the HT coil and the rotor cup. The motor had HD electronic ignition before. Apart from purchasing the DS6-1 ignition what else do I need to complete the installation? View answer
Asked 4 ´years ago
I currently have the V&H FP3 on my bike, I am wanting to ditch it the problem is I use the sensor readouts as my instruments due to my handlebars blocking my speedo/tach.does the PV4 give you information such as speed, rpm, oil temp etc. on the screen? View answer
Asked 3 ´years ago | Power Vision 4 for 2011-2020 Harley Davidson
Will this work in California? View answer
Asked 4 ´years ago | POWER VISION FOR 2021+ HARLEY-DAVIDSON
Will this fit a 2017 harley davidson fxdf fat bob dyna? View answer
Asked 1 ´year ago
Can you provide a tune for XSR900 with M4 exhaust, stock air filter? View answer
Asked 4 ´years ago
does it work with 2021 SM? View answer
Asked 4 ´years ago
WHAT DOES THIS FIT AND WHAT DIAGNOSTIC EQUIPMENT DOES THIS WORK WITH? View answer
Asked 4 ´years ago
I installed the Dyna 2000 on my 1979 Cb750k project. There is 12v keyed power and ground at plug on unit but will not power up. Would it be possible to get a diagram of functions of each wire going into controller. Also could there be any other reason that with power and ground the brand new unit would not power up? View answer
Asked 4 ´years ago
Hello Dynatek, i am looking for the correct igntion system for my bike (Harley davidson, softail Nostalgia, 1994 carb, ) i have been told that the nose cone part i need is the 2101-0027 part number, 2000i 1986-2003, but i am unsure which coil i need? if you could point me in the right direction i would be very grateful, i am looking for a single fire coil that i can mount in the original coil position on the softail. many thanks Simon. View answer
Asked 4 ´years ago
So I have a "POWER VISION BLACK SERIES FOR ALL CAN ECM HARLEY-DAVIDSON MODELS" that I got for an old bike that was stolen, but never used it to flash that bike. With my new bike, which is a 2022 Lowrider ST, would this cable work with that controller and bike so that I can use the tuner with my new bike? View answer
Asked 3 ´years ago
Please let me know if there are more available flash for 2018 R1. There was only one available at this time for Akrapovic slip-on, stock air filter. If I can adjust and be provided the password through C3 tuning software would be great. Please email at msosa06@yahoo.com for assistance. View answer
Asked 3 ´years ago
what year models does this tune license cover? View answer
Asked 4 ´years ago
Will this work on my 2021 outlander xtp 1000 View answer
Asked 4 ´years ago | Power Vision 3 for Can-Am Outlander
I have an 04 R6, which rod am I supposed to cut to make it work as the installation manual doesn't show where from what I saw? Along with that is there a certain amount of threads that must be shown for the sensor to be 'clicked' or noticed? Just because mine is plugged in but is not recognizing that the shifter is being activated. View answer
Asked 3 ´years ago
